Zero Leakage System
Zero Leakage System Overview
Zero Leakage System® offers a variety of fibrous flexible compounds, replacing
compression packing in the stuffing box.
This material evenly surrounds the shaft and works like a lubricated plug, eliminating pressure
points.
It ensures minimal friction, extended sleeve life due to no scoring and provides significant energy
savings.
Zero Leakage System is available in various synthetic fibers, mixed with tixotropic and other lubricants.
It is pressure treated to ensure uniform dispersion.
Braided Packing Operational Cost
55% Product loss due to machine downtime
25% Value of leaked fluid
15% Labor cost
5% Packing purchase cost
Packing Operational Cost With Zero Leakage System
0% Product loss due to machine downtime
0% Value of leaked fluid
15% Labor cost
5% Packing purchase cost
| Braided packing | Zero Leakage System |
|---|---|
| ✕Leakage is necessary for lubrication. Optimal rate generally varies from 30 to 50 drops per minute, which can represent a yearly loss of more than 1200 lt (320 gal) of product. | ✓With a correct application, and under optimal mechanic conditions of the pump, leakage can be as low as Zero. |
| ✕Packing require frequent replacements, causing machine shutdown and loss of production. | ✓After the first application, there is no replacement. Zero Leakage System is only refilled, without stopping the machine. |
| ✕Cooling made through lantern ring requires high water consumption. Packing compression reduces its effectiveness. | ✓No cooling or flushing is required. |
| ✕To ensure prompt replacement, each packing size employed in a plant must have a large backup inventory. Demand peaks for a given size can cause downtime if not enough packing are on stock. | ✓The same inventory can be used for stuffing boxes of ALL sizes and standards in the plant. Total inventory required for prompt replacement of all the plant’s equipment is considerably lower. Stock control is easy, demand peaks are unlikely as ZLS is slowly refilled rather than replaced. |
| ✕Friction, especially with harder fibers that are needed for abrasive fluids, causes a very high absorption of power and a quick wear of the sleeve. | ✓While friction against the sleeve does take place, the self-lubricating fibers reduce it to only a fraction, if compared with braided packing. |
How It Works
1 Install an anti-extrusion ring of braided packing or solid PTFE.
2 Hand fill stuffing box with compound, using gland follower to compact.
3 Install an anti-extrusion braided packing ring or a solid PTFE washer at gland side and “close” with stuffing box gland.
4 Tighten gland nuts to compress the compound and start up pump valve.
PTFE + Graphite
| T °C | -80 ÷ +280 | ||
| P bar | 20 | 35 | 70 |
| V m/sec | 20 | 8 | 4 |
| pH | 0 ÷ 14 | ||
| Vol | 615 cm3/Kg | ||
Twaron® Fibers
| T °C | -35 ÷ +260 | ||
| P bar | 25 | 40 | 80 |
| V m/sec | 18 | 4 | 2 |
| pH | 2 ÷ 13 | ||
| Vol | 830 cm3/Kg | ||
PTFE Fibers
Injectable packing compound made of virgin PTFE textured fibres and special inert lubricants for extremely high performances.
Meets FDA requirements. Ideal for packing pumps and valves in food plants, pharmaceutical and chemical industries and drinking water production.
No flushing is required, can be compressed close to “zero leakage”.
| T °C | -80 ÷ +260 | ||
| P bar | 20 | 30 | 60 |
| V m/sec | 8 | 3 | 1 |
| pH | 0 ÷ 14 | ||
| Vol | 640 cm3/Kg | ||
Expanded Graphite
Injectable packing compound designed for heavy duty applications of high temperature and pressure, made of 100% expanded pure graphite. Suitable for steam valves, boiler feed and hot oil pumps, etc. No shaft or sleeve scoring. Highly recommended for use on old equipment in bad mechanical conditions.
| T °C | -30 ÷ +600 | ||
| P bar | 40 | 70 | 90 |
| V m/sec | 25 | 5 | 2 |
| pH | 0 ÷ 14 | ||
| Vol | 710 cm3/Kg | ||
Unbleached PTFE
| T °C | -40 ÷ +260 | ||
| P bar | 20 | 30 | 60 |
| V m/sec | 8 | 3 | 1 |
| pH | 0 ÷ 14 | ||
| Vol | 610 cm3/Kg | ||
Unbleached PTFE
Pure virgin Twaron® fibers mixed with expanded mineral graphite flakes and special tixotropic heat resistant lubricants. This compound is designed for use in heavy duty pumps and valve applications, such as hot water, steam and diathermic oils, due to its excellent capacity for heat dissipation.
Available also as Style P99 GP, containing anti friction metal pellets, for specific use in applications with worn shafts or pumps in bad mechanical condition.
| T °C | -20 ÷ +300 | ||
| P bar | 30 | 50 | 80 |
| V m/sec | 20 | 5 | 1 |
| pH | 1 ÷ 13 | ||
| Vol | 620 cm3/Kg | ||